Bassface DB1.1 1400w 1Ohm Class D Monoblock Car Subwoofer Amplifier Mono Sub Amp

132 In Stock

RRP: £135.99
£108.99
  • Website Exclusive Price*** Does not apply in Store
  • Express Delivery also available

Now shipping Version 4 of this product - DB1.1 is technologically very far advanced now. Newly updated for 2017 and almost five years of development down the line the latest DB1.1 is taken into the digital age with a new class-D board. This means its now properly 1 Ohm stable. The amplifier ships with a remote level controller to allow on the fly fine tuning of settings. An adjustable sub-sonic filter lets you keep the power going to where you want it and a bass boost can help maximize output from your subwoofer set up. We included two output terminal pairs to make it easier for you to connect two subwoofers or dual voice coil subwoofers to the one amplifier. Just like its DB family members, the DB1.1 is built around a striking and beautiful heat-sink. It's not just there to look good but also to optimise passive air convection over the amplifier which will keep the amp running cooler for longer.

Product Data

  • Bassface SKU : DB1.1
  • Product Category : Amplifiers
  • Version : 4
  • Bassface Series : Assault Series
  • Barcode : 683422298400
  • Product Net Weight (g) : 3150
  • Product Height (mm) : 62
  • Product Length (mm) : 242
  • Product Width (mm) : 242
  • Complete Product Pack Weight (g) : 3520
  • Retail Carton L (mm) : 278
  • Retail Carton W (mm) : 243
  • Retail Carton H (mm) : 62
  • Sold As : Single
  • Disclaimer : Please take when installing your amplifier and be sure to read the Instruction manual on correct set up and Installation. Earthing an amplifier is extremely important and should be done correctly to ensure long life and protection of your product. Please refer to the Images provided and the Online Instruction Manual

Technical Highlights

  • Latest Version Of Our Incredible Inexpensive Yet Powerful Bass Amplifier
  • Variable Bass Boost
  • Highly Efficient Class D Topology
  • K3 Logic Circuit for highly accurate audio rendition
  • Up To 6V Ready Pre Amp Input Stage
  • Variable Low Pass Crossover
  • Low THD Audiophile Components
  • Cast Aluminium Heatsink Body
  • Variable Bass Boost Frequency
  • Thermally Efficient Heatsink Coating
  • Variable Subsonic Filter
  • T.D.O.S. Amplifier Protection Circuitry
  • O.P.S. Oversized Power Supply
  • Line output for daisy chain amplifier applications

Head Unit Data

Crossover Data

TS Parameters

Speaker Data

Tweeter Data

Amplifier Data

  • Maximum Unfused Power (Watts) : 1400
  • Maximum Unfused RMS (Watts) : 700
  • RMS Per Channel 4 Ohm (Watts) : 400
  • RMS Per Channel 2 Ohm (Watts) : 650
  • RMS Per Channel 1 Ohm (Watts) : 700
  • Amplifier Frequency Response (Hz) : 10-1000
  • Amplifier THD Continous 4 Ohm 1Khz(100Hz) (%) : <0.1
  • Amplifier Signal To Noise Ratio (db) : >98
  • Amplifier LPF (Hz) : 40-180
  • Amplifier Bass Boost (Db) : 0-12
  • Amplifier Boost Frequency (Hz) : 30-80
  • Amplifier Subsonic Filter (Hz) : 15-50
  • Amplifier Audio Signal Input Voltage (V) : 0.2-6
  • Amplifier LPF Slope (Db)(Oct) : 12
  • Amplifier Subsonic Filter Slope (Db)(Oct) : 12
  • Amplifier Topology : Class D
  • Amplifier Fuse Rating (Amps) : 80
  • Amplifier Power Wire Input Gauge (AWG) : 4
  • Recommended Wiring Kit and Accessories : PWK4.1 RCA5.1
  • Minimum Recommend Final Load Per Channel (Ohms) : 1

Battery Data

Whats In The Box?

  • 1 x High Performance Mono Amplifier
  • 1 x Bass remote level control
  • 1 x 5m level control cable
  • 4 x Self tapping screws
Thompsons Ltd

Specification


Close Clear All