Bassface DB2.2 3200w 2/1 Channel Bridgeable Stereo 12v Power Amplifier

43 In Stock

RRP: £453.99
£338.51
  • Includes Free UK Delivery on Basket Orders Over £50.00***
  • Express Delivery also available
  • ***Vehicle Batteries Not Included

Now shipping Version 2 of this product - DB2.2 is a power house 2 channel amplifier. Boasting over 500W RMS per channel into 4Ohms. This amp is quite a leap from the DB2.1 with totally different heatsink body and a much larger form factor. The DB2.2 has been designed to fulfil the needs of our competition customers. The amp has been built with SQ in mind over SPL. Although it develops extremely high power output, the electronics are all carefully selected and matched to give you an impressive 0.04% THD (Distortion) at full power on 4Ohm. So even at extreme output levels, the sound will be very clear and tonally balanced. We included steep 24db/oct LPF as well as HPF as the amp is so big it lends itself well to powering SQ subwoofer set ups, where the big bad digital amps fall short of giving that warmth you get from Class A/B. On that note, we also included a remote level control, as you would expect to get with a decent subwoofer amplifier. The internal power supply is overbuilt to enable the amp to work very hard without fatiguing other components and not drop below its rated output. When using this amplifier at maximum performance be sure to grant adequate cooling - this monster draws enormous current and produces enormous power!

Product Data

  • Bassface SKU : DB2.2
  • Product Category : Amplifiers
  • Version : 2
  • Bassface Series : Hammer Series
  • Barcode : 617529407724
  • Product Net Weight (g) : 6450
  • Product Height (mm) : 60
  • Product Length (mm) : 530
  • Product Width (mm) : 240
  • Complete Product Pack Weight (g) : 6550
  • Retail Carton L (mm) : 550
  • Retail Carton W (mm) : 236
  • Retail Carton H (mm) : 53
  • Sold As : Single

Technical Highlights

  • High Fidelity Class A/B Topology
  • Extremely Robust Oversize Power Supply
  • S/N Ratio: >100Db
  • Soft Turn On/Off
  • Variable Low Pass filter at 24db/oct
  • Variable High Pass filter at 24db/oct
  • Variable Bass Boost
  • Fuse Requirements: 40A x 4
  • T.D.O.S. Amplifier Protection Circuitry
  • O.P.S. Oversized Power Supply
  • Up To 6V Ready Pre Amp Input Stage
  • Ultra Low THD Audiophile Components
  • High Density Cast Aluminium Heatsink Body
  • Thermally Efficient Heat-sink Coating
  • Line Out For Multi Amp Systems
  • Gold Plated Connections
  • Double Sided PCB Circuit Board
  • Remote Level Control (Included)
  • Low THD Audiophile Components
  • High Density Cast Aluminium Heatsink Body
  • Thermally Efficient Heat-sink Coating
  • Line Out For Multi Amp Systems

Head Unit Data

Crossover Data

TS Parameters

Speaker Data

Tweeter Data

Amplifier Data

  • Maximum Unfused Power (Watts) : 3200
  • Maximum Unfused RMS (Watts) : 1600
  • RMS Per Channel 4 Ohm (Watts) : 500
  • RMS Per Channel 2 Ohm (Watts) : 800
  • Amplifier Frequency Response (Hz) : 10-25000
  • Amplifier THD Continous 4 Ohm 1Khz(100Hz) (%) : <0.04
  • Amplifier Signal To Noise Ratio (db) : >100
  • Amplifier LPF (Hz) : 50-500
  • Amplifier HPF (Hz) : 50-1200
  • Amplifier Bass Boost (Db) : 0-15
  • Amplifier Boost Frequency (Hz) : 40
  • Amplifier Audio Signal Input Voltage (V) : 0.2-8
  • Amplifier LPF Slope (Db)(Oct) : 24
  • Amplifier HPF Slope (Db)(Oct) : 24
  • Amplifier Topology : Class A/B
  • Amplifier Fuse Rating (Amps) : 160
  • Amplifier Power Wire Input Gauge (AWG) : 0
  • Recommended Wiring Kit and Accessories : PWK0.1 RCA5.1
  • Minimum Recommend Final Load Per Channel (Ohms) : 2
  • Amplifier Channel Separation (Db) : >60

Battery Data

Whats In The Box?

  • 1 1 x High Performance Mono Amplifier
  • 2 1 x Remote level control
  • 3 1 x 5m level control cable
  • 4 4 x Self tapping screws
  • 5 4 x 40A Spare Fuses
Thompsons

Specification


Close Clear All